Confirm Biosciences Babyprep Home Ovulation Test Kit (Case of 6, 7 Test Kits Per Box)
The BabyPrep One Step Ovulation Urine Test is a efficient and qualitative test used to predict when there is a LH surge, and in turn, when you are likely to ovulate. The BabyPrep One Step Ovulation Predictor is easy to use and easy to read. Simply hold the absorbent tip in your urine stream. Results will appear in as early as 3 minutes.
A pink line in the test window, that is the same color as, or darker than, the line in the reference window, lets you know that you should ovulate within 24-48 hours.
Features and Benefits:
How Does It Work?
- Ovulation test is easy to use & read
- Gives 99% accurate results
- Predicts ovulation 24 to 48 hours in advance
- Gives you results in 3 minutes
- Results 5 days before missed period
- Includes seven ovulation tests
- Includes a bonus pregnancy test
- Bonus pregnancy strip test included
- FDA Cleared, CE Marked & CLIA Waived
The LH (Luteinizing Hormone) which is in the urine of normal women will increase dramatically in the middle of the menstrual cycle. The LH increase triggers ovulation which is when the egg is released periodically from Normal fertile women. WHO experts state that LH testing is a reliable way to detect ovulation. Ovulation will occur after 24-48 hours following a positive test.
When specimen is applied to a midstream, capillary action carries the specimen to migrate along the membrane. When LH in the specimen reaches the test zone region of the membrane, it will form a colored line. Absence of this colored line suggests a negative result.
To serve as a procedure control, a colored line will appear at the control zone region, if the test has been performed properly.
The test device detects ovulation with a high degree of certainty. It is a valuable tool in helping to achieve pregnancy since it determines the period that the egg and the sperm cells will meet in the best conditions.
Ovulation may be irregular because of circumstances, emotions and other factors in your life. You cannot presume that ovulation always occurs at the same time after menstruation. Therefore, you should test again in each menstrual cycle.
When To Collect Urine For The Test?
Any urine specimen is appropriate for ovulation testing.
How To Collect Urine?
Urine specimens may be collected in any clean, dry, plastic or glass container.
When To Begin Testing?
The length of the menstrual cycle is the duration from your first menstrual bleeding day to the day before the next bleeding begins. Determine the length of menstrual cycle before test. Please refer to the chart below to determine when you should start testing. If your cycle is shorter than 21 days or longer than 38 days, consult a physician. If you do not know your cycle length, you may begin the test 11 days after your first period since the average cycle length is 28 days. Perform 1 test each day over a 5 days period, or until the LH surge has been detected.
Seven BabyPrep Ovulation Test Kits
One Pregnancy Test Strip
Leaflet with instructions for use
- To begin testing, open the sealed pouch by tearing along the notch. Remove test device-midstream from the pouch.
- Hold the round end of cover with one hand. Use the other hand to pull out the midstream cap and expose the absorbent.
- Point the absorbent tip downward; place the absorbent tip in urine stream for at least 10 seconds to be thoroughly wet
How To Read The Results?
- Re-cap the device and wait for color bands to appear. Read the result in five minutes. Do not read results after more than 5 minutes.
Negative (no LH Surge): Only one color band appears on the control region, or the test band appears but is lighter than the control band. This means there is no LH surge.
Positive (LH Surge): If two color bands are visible, and the test band is equal to or darker than the control band, one will probably ovulate in the next 24-48 hours. If trying to get pregnant, the best time to have intercourse is after 24 but before 48 hours.
Invalid: No visible bands at all or there are a visible band only in the test region but not in the control region. Repeat with a new test kit. If test still fails, please contact the distributor or the store where you bought the product, with the lot number.